Winfield Heating and Cooling Services

Completed annual furnace tune-up and maintenance inspection on one-year-old unit installed by Blue Frost. Performed comprehensive system check including burner inspection, heat exchanger examination, blower motor operation verification, and filter assessment. All components found operating within manufacturer specifications with no issues identified. System tested and confirmed to be functioning properly for the heating season.

Removed and disposed of existing kitchen faucet and successfully installed client-provided replacement unit. Performed water heater flush service to remove sediment buildup and maintain system efficiency. All plumbing connections tested and verified leak-free, with one-year labor warranty provided on installation work.

Completed comprehensive BFMA tune-up service on 13-year-old residential furnace and humidifier system. Performed furnace maintenance including inspection of heat exchanger, burner assembly, and blower components, verified proper airflow through ductwork, and tested all safety controls. Replaced #10 humidifier pad, inspected condensate drainage system including PVC piping, and confirmed all mechanical and electrical systems operating within manufacturer specifications.

Completed commercial RTU and furnace tune-up maintenance at facility. Performed electrical diagnostics on air conditioning unit, measuring compressor amperage at 6.51A using clamp meter to verify proper operation. Inspected furnace unit and ductwork in mechanical room, noting filters require replacement. Picked up replacement filters from headquarters and provided estimate for filter change service. All equipment operational at time of service completion.

Completed comprehensive BFMA tune-up service on two 8-year-old furnace units located in lower level mechanical room. Performed full system inspection, cleaned burner assemblies, checked and adjusted gas pressure, tested ignition systems, verified proper airflow through heat exchangers, inspected and cleaned blower assemblies, replaced air filters, checked electrical connections and control boards, tested safety switches and limit controls, verified proper venting and combustion air supply, and confirmed both units operating within manufacturer specifications. All systems tested and left in proper working condition.

Responded to no hot water complaint at kitchen sink while all other fixtures had hot water. Upon inspection, identified issue was isolated to single fixture rather than water heater malfunction. Water heater and associated plumbing infrastructure found in proper working condition with circulator pump, shut-off valves, and connections functioning normally. Determined kitchen faucet cartridge or supply line issue requiring further investigation at fixture location.

Completed comprehensive BFMA tune-up service on residential gas furnace unit, equipment age 3+ years. Performed standard maintenance protocol including filter inspection (16x25x1 size verified), visual inspection of heat exchanger, burner assembly cleaning and adjustment, blower motor lubrication, electrical connection testing, thermostat calibration check, and combustion analysis to ensure safe and efficient operation. All components found operating within manufacturer specifications, system returned to service with no issues noted.

Responded to sump pump failure caused by burned-out motor unit. Upon arrival, assessed existing sump pump installation in basement environment showing significant historical water infiltration and moisture damage to surrounding concrete block walls. Removed failed pump from circular sump pit and verified electrical connections and discharge piping configuration. Installed replacement sump pump unit, reconnected white PVC discharge pipe with proper check valve assembly, and secured all electrical wiring according to code requirements. Tested pump operation including float switch functionality to ensure proper activation and water evacuation. Verified discharge flow through existing piping system and confirmed system cycling correctly under simulated conditions.

Completed comprehensive fall maintenance tune-up on 10-year-old furnace system in accordance with preventive maintenance plan requirements. Performed full system inspection including burner assembly cleaning, heat exchanger examination, blower motor lubrication, air filter replacement, and electrical connection verification. All components tested and operating within manufacturer specifications with no deficiencies identified; system ready for heating season.

Completed routine BFMA tune-up on residential gas furnace system located in basement. Performed comprehensive inspection of all heating components including gas valve assembly, flame sensor rod, ignition system, and electrical connections. Cleaned and tested flame sensor, verified proper gas flow operation, inspected all wiring harnesses and connections for secure mounting, and confirmed all safety controls functioning within manufacturer specifications. System operational with no deficiencies noted.

Completed comprehensive BFMA tune-up on 8-year-old furnace system during scheduled morning appointment. Performed full inspection of blower assembly, burner components, gas valve, and electrical controls; noted dust accumulation on blower wheel and housing with some staining present but within normal operational parameters. Cleaned and serviced all accessible components, verified proper operation of all safety controls including pressure switches and flame sensors, confirmed secure wiring connections throughout control board assembly, and tested system for proper ignition sequence and heating cycle performance.

Completed comprehensive BFMA preventive maintenance tune-up on 10-year-old commercial furnace system. Performed electrical diagnostics with multimeter confirming proper voltage readings at 114V, inspected all internal components including wiring harnesses, gas valve assembly, and copper refrigerant lines for proper connections and wear. Evaluated heat exchanger and condensate trap for corrosion and oxidation, documented existing patina on metallic surfaces, verified all mechanical connections and fittings are secure, and confirmed system operational parameters meet manufacturer specifications for continued reliable performance.

Performed comprehensive duct cleaning service on residential HVAC system. Thoroughly cleaned interior ductwork, removing accumulated dust, lint, and debris buildup from ribbed metal ventilation pipes and blower wheel assembly. System airflow restored to optimal performance with all components left in clean, functional condition.

Completed comprehensive BFMA tune-up service on 8-year-old furnace system including humidifier maintenance with #35 pad replacement. Inspected and serviced air handler unit, verified proper filter installation and condition, checked electrical connections and ductwork penetrations, and ensured all HVAC components were operating within manufacturer specifications.

Responded to clogged drain service call at residential property. Upon arrival, inspected bathroom vanity sink and determined blockage was affecting drainage. Cleared obstruction from drain line and verified proper water flow through fixture. Tested drainage system to ensure complete resolution and proper operation of plumbing components.

Replaced defective inducer motor on residential heating unit. Removed old motor assembly, installed new inducer motor, verified proper wiring connections, and tested system operation to ensure correct draft and ignition sequence.

Responded to intermittent water leak in laundry room originating from HVAC unit. Upon inspection, identified condensate drainage issue with PVC piping system connected to condensate pump. Reconfigured and secured condensate drain lines, verified proper pitch and connections to ensure adequate drainage from air handler. Tested system operation and confirmed no active leaking; towels placed on floor to monitor for any residual moisture.

Completed comprehensive BFMA tune-up on 9-year-old furnace system including full furnace maintenance, humidifier service, and semi-annual filter replacement. Performed standard diagnostic checks, cleaned and inspected all furnace components, serviced humidifier unit, and installed new air filter to ensure optimal system performance for the heating season. All equipment tested and operating within manufacturer specifications upon completion.

Responded to service call for non-operational thermostat at commercial facility. Upon arrival, inspected existing Ecobee smart thermostat mounted on interior wall. Performed diagnostic testing and troubleshooting procedures to identify root cause of malfunction. Restored thermostat to full operational status, verified proper communication with HVAC system, and confirmed accurate temperature readings and control functionality.

# HVAC Service - No Heat Call Responded to no heat call on 7-year-old furnace located in closet/utility/laundry room. Upon arrival, performed diagnostic inspection of furnace control system and gas valve assembly. Accessed control panel and examined circuit boards, wiring harnesses, and electronic components for proper operation. Inspected gas valve, burner manifold, and associated piping for functionality and safety. Verified all electrical connections, including multi-conductor wiring and control circuits. Documented equipment condition through photographs showing control board assembly and gas valve system. All components inspected and tested to restore heating operation. System returned to normal working condition.