Service-oriented HVAC and Air Quality Solutions in Streamwood

Performed a complete tune-up on a 12-year-old gas furnace, including inspection of the inducer motor assembly, pressure switch, and wiring connections, and verified blower motor amperage with a clamp meter (0.69 A reading). Inspected the blower assembly and found heavy dust and debris buildup on the squirrel-cage wheel blades, along with surface rust on the motor shaft end, which should be monitored for future service needs.

Performed a seasonal tune-up on a 7+ year-old gas furnace and water heater, including inspection of the cabinet, control board, low-voltage wiring, and flue connections. Measured blower motor amperage with a clamp meter (4.15 A AC) to verify normal electrical operation, and inspected the galvanized supply ductwork, noting minor surface oxidation at one seam with no air leakage or structural damage evident. Equipment was found operating within normal parameters with no visible rust, frost, or component damage.

Performed a complete furnace tune-up on 4+ year-old equipment, including verification of thermostat operation in heat mode and inspection of the gas supply piping at the exterior meter. Observed corrosion and rust on the gas meter piping and fittings, which should be monitored and evaluated for potential corrective action by the utility or a licensed gas technician.

Completed comprehensive BFMA furnace tune-up service on residential heating system as part of new recurring maintenance agreement. Performed full inspection of furnace components, burner assembly, heat exchanger, blower motor, and all safety controls to ensure optimal operation and efficiency. Documented equipment condition with photos of mechanical room layout showing furnace, Bradford White water heater, and associated utility connections for maintenance records.

Completed comprehensive duct cleaning service for residential HVAC system. Removed accumulated dust, debris, and contaminants from ductwork, including feather and organic material buildup. Inspected and replaced dirty pleated air filter showing significant dust accumulation to restore proper airflow and system efficiency.

Replaced UV bulb in Aprilaire air purifier as part of scheduled maintenance. Part was staged at headquarters prior to service call, ensuring efficient completion of the repair.

Completed comprehensive BFMA tune-up service on 8-year-old heating system, including furnace and humidifier maintenance. Performed thorough inspection of blower wheel assembly, confirming proper blade alignment and operational integrity of squirrel cage fan configuration. Examined gas burner assembly and control system, verifying all burner tubes, electrical connections, wiring infrastructure, and control board components for proper function and safety compliance. All system components inspected, cleaned as needed, and confirmed to be operating within manufacturer specifications.

Completed comprehensive BFMA furnace tune-up on residential vertical gas furnace unit installed in confined closet space. Performed electrical diagnostics using digital multimeter, verifying voltage readings at 132V and testing all electrical connections throughout the system including blower motor assembly, gas valve controls, and safety circuits. Inspected heat exchanger condition, confirmed proper operation of all mechanical components, verified adequate clearances, and ensured system meets manufacturer specifications for continued safe operation.

Completed comprehensive BFMA furnace tune-up on 6-year-old heating system. Performed full inspection of furnace components, verified thermostat operation at 73°F setpoint, inspected control board wiring and connections, checked filter size specifications (20x24x1), and documented system condition with photos. All components found operating within normal parameters with no immediate concerns noted.

Completed commercial BFMA preventive maintenance tune-up on two rooftop units and two hanging units. Performed comprehensive system inspections, replaced air filters on both RTU systems with 16x16x2 and 16x10x2 pleated filters, and conducted furnace service procedures per maintenance schedule. All equipment found operating within normal parameters with no deficiencies noted.

Completed comprehensive BFMA tune-up service on outdoor air conditioning condenser unit aged 4+ years. Unit exhibited heavy accumulation of dirt, dust, and debris on exterior panels, filter covers, and aluminum cooling fins, with visible damage to fin spacing and compression in several areas. Performed thorough cleaning of condenser coils, straightened bent fins to restore proper airflow, removed caked-on debris from exterior surfaces and filter components, and cleared vegetation growth from base perimeter. Inspected electrical connections at service panels and conduit runs, verified proper operation of all components, and restored unit to optimal efficiency standards. System now operating within manufacturer specifications following maintenance protocol.

Conducted comprehensive full system HVAC estimate at residential property. Evaluated existing outdoor air conditioning unit showing significant age-related deterioration including extensive rust staining on top panel and weathered components, indicating need for replacement. Inspected basement mechanical area and assessed existing ductwork configuration including metallic supply ducts and flexible return duct system suspended from floor joists. Documented water heater location and existing HVAC infrastructure layout to determine proper equipment sizing and installation requirements. Photographed exterior condensing unit positioned on concrete pad adjacent to home and interior mechanical space to provide accurate proposal for complete system replacement including new furnace and air conditioning equipment.

Responded to water leak in front of furnace. Upon arrival, found active water leakage and shut down unit for safety. Inspection revealed severely corroded evaporator coil with significant rust deterioration at top edge and mounting frame, along with corroded drain piping connections showing moisture streaking. Cleaned up standing water and documented extensive corrosion damage requiring coil replacement to prevent future leaks and restore proper system operation.

Responded to service call regarding potential venting or intake concerns on a four-year-old furnace system. Upon arrival, performed comprehensive inspection of furnace operation, venting system, and air intake pathways. Verified proper combustion air supply and exhaust venting configuration. Conducted routine maintenance service including filter inspection, burner examination, and system performance testing. Inspected evaporator coil and noted significant frost accumulation indicating potential airflow restriction or refrigerant issue requiring attention. Documented all findings with photographic evidence. System confirmed operational at time of service, though frost buildup on coils suggests underlying issue that may impact long-term performance and efficiency.

Completed comprehensive BFMA tune-up on 11-month-old residential air conditioning system. Performed standard preventive maintenance protocol including inspection of condenser unit, compressor, and refrigerant lines. Removed top grille to access and inspect cylindrical heat exchanger coil, noting light dust accumulation on concentric fins typical for equipment age. Verified proper operation of compressor unit, checked copper refrigerant line connections and insulation integrity, and inspected electrical connections for security. All components found operating within normal parameters with no deficiencies requiring immediate attention. Unit returned to service in optimal condition.

Senior technician returned to evaluate compressor condition and warranty status as requested. Upon thorough inspection of the outdoor unit, confirmed compressor failure with visible signs of age, oxidation, and mechanical wear. Verified electrical connections, assessed coil condition, and documented component deterioration with photographic evidence. Checked warranty coverage and determined compressor replacement was necessary to restore system functionality.

Completed comprehensive BFMA tune-up service on residential air conditioning system over 4 years old. Performed standard maintenance protocol including removal of top grille to access condenser unit, inspected compressor assembly and refrigerant lines, verified fan motor operation and blade condition, and assessed heat exchanger coil fins for proper airflow. Cleaned debris and accumulated dirt from internal components and exterior housing, documented equipment condition with photos showing normal wear consistent with age and outdoor exposure.

Responded to no cooling call on Lennox 13ACX-030 residential air conditioning system. Upon arrival, inspected outdoor condenser unit and verified unit specifications. System appeared to be in operational condition with no visible damage to exterior components or electrical connections. Condenser unit showed normal wear consistent with age but remained structurally sound. Cleared debris and leaves from base of unit to ensure proper airflow. Further diagnostics would be required at thermostat and indoor air handler to determine root cause of no cooling complaint and verify whether thermostat replacement is necessary or if issue lies elsewhere in the system.

Completed installation of a 40-gallon residential tanked water heater as a first-time service call. Installed new unit with proper plumbing connections including copper supply lines, galvanized piping, gas line hookup with flexible yellow connector, and appropriate venting configuration. All connections secured with brass fittings and valves, drain valve installed, and unit positioned in utility room alongside existing HVAC equipment with adequate clearance for maintenance and code compliance.

# BFMA Tune Up - Air Conditioning System Maintenance Performed comprehensive BFMA tune-up service on a 7-year-old residential air conditioning system. Upon arrival, conducted visual inspection of outdoor condensing unit, which revealed significant accumulation of dust, dirt, and debris throughout the condenser coil fins. The coil surfaces displayed heavy buildup settled into the grooves between fins, reducing heat transfer efficiency and restricting airflow. Noted extensive vegetation growth around and over the outdoor unit, with weeds, vines, and leafy plants encroaching on the equipment. This overgrowth posed risk of reduced airflow, potential damage to components, and decreased system performance. Removed top panel to access interior components for thorough inspection and cleaning. Cleaned condenser coil assembly using appropriate methods to remove accumulated debris from the spiral-finned surfaces, restoring proper airflow through the heat exchanger. Cleared vegetation from arou