Heating & Air Conditioning Services In South Elgin, IL

Performed a complete furnace tune-up on a 10-year-old gas furnace, including inspection and cleaning of the ignition system and flame sensing components, evaluation of the burner and control board connections, and verification of proper furnace operation. Equipment was found in good working condition with no visible signs of rust, frost, or damage, and the unit was left operating normally.

Performed a scheduled tune-up on a 4-year-old upright gas furnace, including inspection of the cabinet, flue venting, gas piping and shutoff valve, electrical connections, and condensate/drain lines. Inspected the supply plenum and ductwork along with the duct liner insulation, and checked the air filter condition and fit. Furnace was left operating normally.

Performed a furnace inspection using a borescope camera and visual examination of the blower compartment and control board. Borescope imagery documented heavy frost and ice accumulation on the finned heat exchange surfaces and surrounding components, and the blower assembly interior showed dust and grime buildup on the cabinet floor. Photographs were captured of all findings for documentation purposes.

Performed a furnace tune-up on a 5+ year old unit, including inspection of the gas-fired components, flue and venting, electrical connections, and overall system operation to verify safe and efficient performance. Visually inspected the adjacent gas water heater, noting the flue pipe and draft hood, gas supply line with shutoff valve, and flexible connectors in good condition with no visible rust, leaks, or corrosion. Also observed the sump pit, discharge piping, and power supply in the basement, with no immediate concerns noted.

Performed a furnace tune-up and replaced the heavily loaded 16x25x1 air filter, which was restricting airflow. Tested for carbon monoxide with a Fieldpiece SCM4 analyzer, with a reading of 0 ppm, and completed the maintenance inspection.

Performed a complete tune-up on the vertical gas furnace, including inspection of the burner assembly, flue venting, gas piping connections, condensate drain, and electrical components, with no leaks, corrosion, or damage observed. Replaced the 20x25x1 FPR 5 pleated return air filter, which showed dust loading, to restore proper airflow, and verified normal operation of the furnace and the installed APCO-X air treatment unit. Completed the water heater check as part of the maintenance visit.

Performed a full-system replacement evaluation on a non-operational 22-year-old basement furnace and AC split system, inspecting the air handler cabinet, evaporator and refrigerant lines, condensate PVC drain runs, and supply ductwork. Documented seam corrosion on the cabinet, deteriorated foil-faced insulation, and aged ductwork and wiring, and reviewed replacement options for both units to restore reliable heating and cooling.

Performed a complete furnace tune-up on a 3+ year-old unit, including inspection of the burner assembly, igniter/flame sensor, and manifold components, with all surfaces checked for proper condition and signs of moisture or condensation. Inspected the return air filter, which showed mild dust accumulation along the pleats, and verified proper filter fit and airflow. System was confirmed operating normally upon completion.

Performed a complete tune-up and inspection on a 12-year-old Trane gas furnace located in a utility closet. Inspected and cleaned the blower assembly, including the squirrel cage wheel, which had accumulated dust and debris buildup affecting airflow. Verified proper operation of the heating cycle, venting, condensate PVC piping, and ductwork connections, with no signs of frost, ice, or rust observed on the equipment.

Completed comprehensive BFMA tune-up on a 9+ year old furnace system during morning service window. Performed standard maintenance procedures including inspection of all mechanical components, burner assembly evaluation, heat exchanger examination, and blower motor assessment. Accessed equipment in utility space and verified proper operation of all system components using appropriate hand tools for equipment adjustments and inspections.

Completed comprehensive furnace tune-up and maintenance inspection on 4-year-old heating system as part of BFMA preventive maintenance program. Performed full system diagnostics, inspected and verified proper operation of blower assembly, heat exchanger, and all safety controls. Checked and confirmed clean air filter in place, examined refrigerant lines for proper insulation and connections, and verified adequate clearances around equipment. All components found operating within manufacturer specifications with no deficiencies noted at time of service.

Completed comprehensive BFMA tune-up service on residential HVAC system including furnace inspection, humidifier maintenance with #35 pad replacement, and semi-annual filter change using #213 filter. Performed electrical diagnostics using clamp meter to verify proper amperage draw and system performance on air handler unit installed in attic space. All components inspected, tested, and confirmed operating within manufacturer specifications with no issues identified.

Completed comprehensive BFMA tune-up service on 7+ year old furnace system during afternoon appointment window. Performed thorough inspection of control board, wiring harnesses, and blower assembly, documented existing dust accumulation on interior components and housing surfaces. All electrical connections verified secure, system operational parameters confirmed within manufacturer specifications, and equipment returned to normal service.

Completed comprehensive furnace tune-up on 1+ year old equipment, arriving after 12:30 PM per customer scheduling requirements. Performed standard maintenance procedures including inspection of all system components, verified proper operation of "The Protector" signal sensor monitoring device with reset and alarm functions, and confirmed backup battery power supply with replacement date marked for 2029. All safety controls, wiring connections, and PVC condensate drainage components inspected and found in satisfactory operating condition.

Responded to after hours service call for HVAC system malfunction. Upon inspection, found blower wheel assembly with moderate dust and debris accumulation affecting airflow efficiency. Examined outdoor condensing unit and identified disorganized wiring connections at control board with multiple loose wire terminations. Cleaned blower wheel assembly, secured all electrical connections, and verified proper system operation before departure.

Responded to residential no cooling call affecting entire home. Arrived on site and performed system diagnostic on Trane HVAC system located in basement mechanical room. Inspected furnace unit, ductwork connections, and associated components including humidifier and auxiliary equipment. Documented equipment condition with photographs showing proper installation and no visible damage to unit or ductwork. System evaluated for cooling failure, all findings recorded for customer review and recommendation of next steps.

Evaluated existing HVAC system with confirmed refrigerant leak in air conditioning unit that was recently recharged but already failing to maintain adequate cooling capacity. Provided comprehensive estimate for complete system replacement including new air conditioning unit and evaporator coil, with options for both Trane and American Standard equipment. Assessed existing furnace for potential replacement to ensure compatibility and optimal system performance with new cooling equipment.

Removed and thoroughly cleaned blower wheel assembly that had accumulated significant dirt and dust buildup affecting system performance. Replaced defective damper component with new part. Reassembled unit, verified proper airflow operation, and confirmed system returned to normal functionality.

Removed and properly disposed of existing residential water heater from basement location. Installed new 75-gallon natural gas Bradford White water heater with 6-year tank warranty and 1-year parts and labor warranty. Modified and connected all required utilities including natural gas line, cold water supply, hot water distribution, and flue venting system to meet current code requirements. Installed necessary safety components including temperature and pressure relief valve with proper discharge piping, gas shut-off valve, and expansion tank. Tested all connections for leaks, verified proper combustion and venting operation, and confirmed unit functionality before completion.

Responded to no-cooling call with thermostat reading 81°F and non-operational fan. Upon inspection of outdoor unit, discovered extensive rodent nesting material packed inside electrical panel, blocking components and preventing proper operation. Cleared all debris from panel, verified electrical connections, and tested capacitor functionality. Restored unit to normal operation with fan cycling properly and system cooling effectively.