Heating, Cooling & Air Quality Services in Elmhurst

Completed comprehensive BFMA furnace tune-up on gas heating system at unit 401. Performed full combustion analysis, inspected burner assembly with active flame operation, verified proper ignition sequence, and cleaned all accessible components. All safety controls tested and confirmed operational, system operating within manufacturer specifications.

Completed residential water heater replacement with installation of a Bradford White 40-gallon tall narrow tank-style unit in basement utility area. Installed new copper supply piping with brass shut-off valves, pressure relief valve with proper discharge piping, and gas control valve assembly with appropriate connections. All work performed to code specifications with proper venting and clearances maintained around HVAC equipment in the mechanical room.

Completed comprehensive BFMA tune-up service on 10-12+ year old HVAC system including air conditioning unit, furnace, and water heater. Performed standard maintenance procedures including inspection of gas valve assembly, burner components, flame sensors, air filter condition, and refrigerant line connections in attic installation. All equipment inspected, cleaned, and tested for proper operation with no deficiencies noted; system operating within manufacturer specifications.

Responded to service call for garage heater unit not operating at optimal performance. Upon arrival, performed diagnostic assessment and system evaluation. Completed necessary service procedures to restore proper heating function to the unit.

Responded to no-heat call for upstairs furnace in two-furnace system. Diagnosed control board failure on Goodman unit, removed and inspected internal components including circuit boards and wiring harnesses. Provided diagnostic findings and repair recommendations to restore heating operation.

Replaced defective blower motor assembly in Trane furnace under manufacturer's warranty coverage. Disconnected existing motor wiring harness, removed failed motor from housing, installed new motor assembly, reconnected all electrical connections, and verified proper operation of heating system.

Completed comprehensive furnace tune-up in basement mechanical room as part of BFMA maintenance agreement. Performed full system inspection, checked all operational components, and replaced 16x25x1 air filter which showed moderate dust accumulation. Noted aging mechanical room environment with visible ceiling deterioration, moisture indicators on walls, and general wear consistent with older installation. All findings documented photographically and communicated directly to property owner per service instructions, with system left in proper working condition.

Completed comprehensive BFMA tune-up on Carrier HVAC system with both heating and air conditioning components, approximately one year old. Performed standard preventive maintenance procedures including inspection of all electrical connections, temperature sensor verification, refrigerant level check, condensate drain line assessment, and system performance testing. All equipment found operating within manufacturer specifications with no deficiencies noted; system cleared for continued operation.

Completed comprehensive furnace tune-up on 5-year-old residential heating system. Performed full system inspection including burner assembly, heat exchanger, evaporator coil, blower motor, electrical connections, and venting components. All components found operating within manufacturer specifications with no deficiencies noted; system cleaned, tested, and returned to service.

Responded to no-cooling complaint on 3-year-old air conditioning system. Upon arrival, unit was displaying E17 fault code. Followed manufacturer diagnostic flowchart to troubleshoot fault, which indicated a motor communication or wiring issue. Verified aerial motor wire connections, tested DC line voltage connectivity, and inspected motor wiring harness per technical diagrams. Resolved fault code, restored system to normal operation, and confirmed proper cooling function before departure.

Completed comprehensive BFMA furnace tune-up and preventative maintenance inspection on 2-year-old heating system. Replaced dirty air filter, inspected gas valve and control board assembly, and documented significant copper pipe corrosion with heavy verdigris oxidation near valve connections requiring future attention. All system components tested and operational upon completion.

Completed comprehensive BFMA preventive maintenance on four 3-year-old rooftop units, including full tune-up procedures, filter replacements, and belt changes on all units. Inspected condenser coils showing moderate dirt and debris accumulation, noted for future cleaning consideration. All blower motors, electrical connections, and drive belts were inspected and replaced as scheduled, with all units tested and confirmed operational upon completion.

Completed comprehensive BFMA tune-up service on residential air conditioning system, performing electrical diagnostics with amp draw readings of 57.9 amps and voltage testing on outdoor unit. The condenser coil exhibited heavy accumulation of dust, debris, lint, and fibrous material throughout the fin assembly, which was addressed during the maintenance service to restore proper airflow and system efficiency.

Completed annual boiler maintenance including inspection of combustion chamber assembly, blower motor, gas valve controls, and all electrical connections. Verified proper operation of ignition system, heat exchanger, digital control board, and all safety devices. Cleaned and tested unit, confirmed all copper piping connections and brass valves secure with no leaks detected.

Completed annual furnace maintenance on a two-year-old unit located in the basement. Performed comprehensive tune-up including inspection of burner assembly, flame sensor, and ignition components. Examined evaporator coil and heat exchanger for proper operation and cleanliness. All components inspected and found to be functioning within normal parameters with no issues identified at time of service.

Completed comprehensive BFMA tune-up service including full furnace inspection and humidifier maintenance on residential HVAC system. Performed standard seasonal maintenance procedures, verified all safety controls, inspected heat exchanger, tested ignition system, checked gas pressure and combustion efficiency, cleaned burner assembly, and evaluated air handler operation. Inspected and serviced whole-home humidifier unit, verified water supply connections, checked drainage system functionality, and confirmed proper integration with heating system. All equipment found operating within manufacturer specifications with no immediate repairs required.

Completed comprehensive duct cleaning service for residential HVAC system. Cleaned all accessible ductwork, main trunk lines, and return air vents throughout the home, removing accumulated dust, debris, and contaminants from the system. Documented pre-service conditions showing significant dust buildup on floor-level return register and verified proper system operation upon completion.

Completed comprehensive tune-up and maintenance service on AO Smith tanked water heater in residential basement utility room. Performed full system inspection including verification of pressure relief valve operation, examination of all plumbing connections and fittings, assessment of venting components, and visual inspection of tank condition. Checked gas line connections, tested safety controls, and verified proper clearances around unit. All components found to be functioning within normal operating parameters with no immediate concerns identified. Unit properly labeled with current safety and warranty information, and installation appears to meet code requirements with appropriate piping configurations in place.

Completed comprehensive BFMA tune-up service on 16-year-old outdoor air conditioning unit. Disassembled cabinet panels to access interior components, which revealed heavy accumulation of dirt, debris, leaves, and organic matter throughout the unit. Performed thorough cleaning of condenser coil, internal components, and cabinet assembly, removing all accumulated contamination to restore proper airflow and system efficiency. Inspected refrigerant lines, electrical connections, and all mechanical components during service. Reassembled unit and verified proper operation upon completion of maintenance protocol.

Completed comprehensive BFMA tune-up service on two air conditioning systems aged 9 and 21 years. Performed standard maintenance procedures including inspection of evaporator coils, verification of refrigerant levels, electrical component testing, and system performance evaluation. Inspected and documented condition of air filtration system, noting dust accumulation on pleated filter and AprilAire air quality monitoring device operation.