Expert HVAC, Air Quality and Plumbing in Hoffman Estates, IL

Performed a furnace tune-up on an 11+ year-old Comfortmaker horizontal furnace/air handler suspended in the attic, inspecting the cabinet, ductwork connections, and gas piping, and verifying safe operation. Carbon monoxide levels were tested with a calibrated meter and measured 0 ppm, with no abnormal readings detected.

Performed a complete tune-up on an 8-year-old gas furnace, inspecting the burner assembly, gas valve, inducer motor, pressure switches, PVC vent connections, and wiring harness for proper operation. Inspected the igniter and flame sensor assembly, noting soot staining and light rust residue at the burner opening, and verified secure mounting hardware. Equipment was found operational with no frost or heavy corrosion present, and the unit was enrolled in a recurring furnace maintenance plan.

Performed scheduled tune-up on 5-year-old gas furnace, including inspection and servicing of major components, and completed seasonal humidifier service with installation of a new #10 water panel pad. Inspected the humidifier supply and drain connections, confirmed proper operation, and checked combustion venting and flue connections at the adjacent water heater area. Recurring furnace and humidifier maintenance plans are active for ongoing seasonal service.

Completed the BFMA tune-up on the Trane gas furnace, including inspection and servicing of the burner and heat exchanger components, airflow and drain line checks, and replacement of the air filters. Performed the dryer vent cleaning and humidifier service, replacing the humidifier components, and confirmed the system is operating properly with no visible rust, frost, or damage.

Performed a complete furnace tune-up on a 3+ year-old unit, inspecting the blower motor and squirrel-cage wheel, internal wiring and connections, and the control compartment components. No signs of damage, frost, or rust were found, and the equipment was left in proper operating condition.

Responded to service call for loud knocking noise coming from residential tanked water heater. Upon arrival, inspected unit and identified sediment buildup in tank causing the knocking sound, commonly known as "kettling." Examined water heater components including temperature and pressure relief valve, gas control valve, and burner assembly. Noted significant corrosion on inlet/outlet piping connections at wall penetration, indicating age-related deterioration of plumbing infrastructure. Flushed water heater tank to remove accumulated sediment and mineral deposits that were causing the noise during heating cycles. Tested unit operation after service and confirmed elimination of knocking sounds. Advised customer of corroded pipe conditions and recommended monitoring for potential future replacement needs.

Completed comprehensive BFMA tune-up on residential furnace system with equipment age of 4+ years. Performed full inspection of blower assembly, confirming proper operation of centrifugal fan wheel with all blades intact and free of debris accumulation. Verified system components, documented equipment condition with photos, and ensured all mechanical systems operating within manufacturer specifications.

Completed comprehensive BFMA tune-up on 7-year-old Trane XR80 furnace system, including full inspection of blower wheel assembly, burner components, and electrical system measurements using clamp meter. Blower wheel and squirrel cage fan showed minimal dust accumulation and proper operation, with all burner orifices inspected and confirmed clean. Sump pump inspection completed as part of routine maintenance protocol, with all components functioning within normal parameters.

Completed comprehensive furnace tune-up maintenance on residential HVAC system as part of preventative maintenance program. Inspected furnace unit with 4+ years of service, verified all safety controls and operational parameters, and documented equipment condition including associated Rheem water heater in mechanical room. System found to be operating within normal specifications with all components functioning properly at time of service.

Completed comprehensive furnace tune-up on 13+ year old heating system. Performed standard maintenance protocol including inspection of all mechanical components, burner assembly cleaning, heat exchanger examination, and safety control testing. Verified proper operation of gas valve, ignition system, and flame sensor. Checked and adjusted airflow, tested thermostat functionality, and confirmed adequate combustion air supply. Inspected venting system for proper draft and clearances. Evaluated condition of water heater plumbing connections and observed aged copper piping with typical oxidation throughout utility area. All furnace components found operational within acceptable parameters for unit age. System running efficiently with no immediate safety concerns identified. Documented equipment condition with photographs for service records.

Performed comprehensive BFMA tune-up on an 11-month-old Trane air conditioning system. Completed full system inspection including condenser unit evaluation, verified electrical connections at disconnect box, checked refrigerant levels, inspected condenser coils and fan operation, and confirmed proper airflow through louvers. Unit operating within manufacturer specifications with all components functioning properly and no issues identified during preventive maintenance service.

Conducted on-site evaluation of existing outdoor condensing unit and indoor coil system for replacement estimate. Unit is 25+ years old and beyond economical repair. Inspected outdoor condenser positioned on concrete pad with gravel surround, noting weathered cabinet condition, aged fan assembly with hexagonal guard, and deteriorated metal casing consistent with extended service life. Evaluated indoor coil location in basement utility area with existing ductwork connections. Documented current system configuration including refrigerant line routing, electrical conduit placement, and mounting specifications. Assessed installation area conditions and confirmed adequate clearances for replacement equipment. Provided comprehensive replacement options for complete air conditioning system including new condensing unit and evaporator coil to restore cooling capacity and improve energy efficiency.

Replaced defective condenser fan motor on outdoor HVAC unit under manufacturer's and Blue Frost labor warranty. Removed old motor assembly, installed new motor, reassembled unit, and verified proper operation with all components functioning correctly.

Completed comprehensive AC tune-up for monthly plan member during scheduled afternoon appointment. Performed full system inspection of outdoor condenser unit and indoor components, noting visible dirt and debris accumulation on condenser coils and exterior grill. Inspected air filter showing normal dust accumulation from use, verified system operating within proper parameters with no immediate service needs identified.

Responded to service call for water leak beneath kitchen sink at drain connection. Upon inspection, identified moisture accumulation in drip pan under cabinet, indicating active or recent leak at drain assembly. Inspected PVC P-trap and drain connections for proper seal and tightness. Addressed leak source at drain tailpiece connection point where drain exits sink basin. Tightened connections and verified proper seal at all drain assembly joints. Tested system for leaks by running water through both sink basins and monitoring drain connections for any signs of moisture. Confirmed repair successful with no active leaking observed. Cabinet interior and drip pan showed evidence of previous water exposure but no active water present after repair completion.

Completed comprehensive BFMA tune-up service on Carrier air conditioning system. Performed electrical diagnostics using digital multimeter to verify capacitor functionality and electrical connections, recording measurements within normal operating parameters. Conducted full system inspection of outdoor condenser unit, confirming proper operation of all components and documenting equipment condition through photographic records.

Completed comprehensive BFMA tune-up service on 12-year-old residential air conditioning system. Performed thorough inspection of outdoor condensing unit, including examination of dual-capacitor configuration with primary run capacitor and BoostCap hard start capacitor. Verified all electrical connections, tested capacitor functionality, and inspected wiring integrity throughout electrical compartment. Cleaned accessible components, checked refrigerant levels, and confirmed proper system operation. Unit tested and left in normal operating condition with all panels secured.

Responded to water leak issue originating from furnace system. Upon inspection, identified aging galvanized steel pipe penetrating through ceiling with visible corrosion, surface deterioration, and water staining. Documented existing plumbing infrastructure condition and leak source with photographic evidence for service records.

Completed comprehensive BFMA tune-up service on outdoor condensing unit aged 4+ years during afternoon appointment window. Performed full system diagnostics with electrical testing using multimeter on capacitor and related components, inspected all wire connections and electrical systems within cabinet, and documented equipment condition including weathered protective covering material and aged metal fin assembly. Unit operational upon service completion with all findings photographed for customer records.

Completed comprehensive BFMA tune-up service on 8+ year old air conditioning system. Upon arrival, found outdoor condenser coil heavily clogged with accumulated dust, dirt, and debris significantly restricting airflow and reducing system efficiency. Thoroughly cleaned evaporator coil assembly, removing thick layer of contamination from fins and copper refrigerant lines. Replaced dirty air filter showing substantial dust buildup with new filter to restore proper airflow and indoor air quality. Performed standard tune-up procedures including system inspection, operational testing, and verification of all components functioning properly. Unit now operating at optimal performance levels with improved airflow and efficiency.