Heating and Cooling Installations Warrenville, IL

Performed a seasonal tune-up on a 9-year-old furnace and air conditioning system. Removed the outdoor condenser's access panels and top cover to expose the coil, which was heavily fouled with dirt and debris restricting airflow across the fins, and inspected the condenser motor and wiring. Documented the adjacent gas water heater and utility closet area as part of the visit.

Performed seasonal tune-up on two furnaces, including electrical diagnostics with a true RMS clamp multimeter to verify component resistance and circuit integrity. Inspected the return air filter and found heavy particulate loading in the pleats, indicating the filter was due for replacement to maintain proper airflow and system efficiency.

Performed a routine tune-up on the approximately three-year-old gas furnace, including inspection of components and verification of proper operation, with electrical readings confirmed using a True RMS clamp meter. Also completed dryer vent cleaning and humidifier service, and the system was operating normally with no deficiencies found. Noted rust and discoloration on the water heater's gas piping and debris in its drain pan, which are recommended for further evaluation.

Responded to a no-heat call on a Trane gas furnace (approx. 5 years old) that was failing to fire. Inspected the gas valve, burner assembly, inducer/pressure switch assembly, and low-voltage wiring and connections, with all components found clean and intact and no visible damage, corrosion, or frost. Verified the furnace is ready for operation and confirmed the homeowner's heating concern was addressed.

Performed a furnace tune-up on 6+ year-old equipment, including inspection of the return air filter (14x24x1) and verification of proper filter seating. Measured blower motor amperage with a true RMS clamp meter (0.86 A reading) and inspected the control wiring, motor, and electrical connections, finding no visible damage, rust, or frost.

Performed tune-ups on two furnaces (4+ years old), including inspection of the ignition and flame sensing components and cleaning of the burner assembly. Removed heavy carbon and soot buildup from the burners and inspected the flame sensor rod and bracket, which showed minor surface oxidation, to ensure reliable ignition and flame proving. Verified the condensate drain and venting, and confirmed proper operation of both units at completion.

Completed comprehensive BFMA tune-up service on 9+ year old furnace and humidifier system. Performed full system inspection, cleaned and tested all components, verified proper operation of heating equipment and humidity control system. All equipment operating within manufacturer specifications upon completion of preventive maintenance service.

Completed comprehensive BFMA tune-up on 5-year-old HVAC system including furnace, air cleaner, and humidifier components. Performed standard maintenance procedures including inspection of blower assembly, ductwork connections, and condensate drainage system. All equipment found operating within normal parameters with no immediate repairs required.

Completed annual preventive maintenance and tune-up on dual Lennox furnace systems installed in 2022. Performed comprehensive inspection of both heating units, including evaluation of internal components, wiring connections, control boards, and air filtration systems. Documented existing filter condition showing normal dust accumulation from regular operation, verified proper wire management and electrical connections throughout both units, and confirmed all mechanical components were functioning within manufacturer specifications for the upcoming heating season.

Completed fall preventative maintenance and tune-up on 6-year-old Trane furnace system. Performed comprehensive inspection of heating equipment, replaced heavily soiled pleated air filter with accumulated dust and debris, verified proper operation of all system components including ductwork and condensate drainage. Unit showed no operational issues and is functioning within manufacturer specifications for the upcoming heating season.

Completed comprehensive BFMA tune-up service on 9+ year old furnace system including humidifier and filter maintenance. Responded to no-heat call and diagnosed heating system failure. Performed complete system inspection, tested all safety controls, cleaned burner assembly, checked gas pressure and flame characteristics, verified proper ignition sequence, inspected heat exchanger for cracks or deterioration, and tested blower motor operation. Serviced humidifier unit including cleaning water panel and verifying proper water flow and drainage. Installed new air filter and cleared condensate drain lines. Inspected all electrical connections, tested thermostat operation, and verified proper venting through PVC exhaust system. Restored heating functionality and confirmed system operating safely within manufacturer specifications. All components now functioning properly with improved efficiency and reliability.

Responded to no heat call for residential property with both furnace and boiler reported as inoperative. Upon arrival, inspected mechanical room housing heating equipment including boiler unit and associated hydronic piping system with expansion tank. Evaluated electrical connections, thermostat signals, and control boards on both heating units. Checked gas supply, pilot assemblies, and ignition systems. Tested pressure switches, limit switches, and safety controls. Verified proper operation of circulator pump and zone valves throughout copper piping distribution system. Restored heat to property and confirmed all heating equipment functioning properly before departure.

Completed comprehensive BFMA tune-up on Lennox residential furnace system (3+ years old). Performed full system inspection, installed new pleated HVAC air filter with CLEAN AIR PURE HVAC filtration media, verified proper airflow through ductwork, and inspected condensate drain line operation. All furnace components tested and operating within manufacturer specifications; unit left in optimal working condition for heating season.

Performed routine maintenance flush on a Bradford White 40-gallon natural gas water heater, model RG140T6N. Drained sediment buildup from tank, flushed system to restore optimal heating efficiency and extend equipment lifespan. Verified all plumbing connections, gas lines, and PVC drain lines were secure and functioning properly upon completion.

Completed comprehensive BFMA tune-up service including furnace and humidifier maintenance on 10-year-old equipment. Performed standard inspection, cleaning, and adjustment procedures on heating system and humidifier unit to ensure optimal winter operation. Documented existing water heater showing significant age-related wear, heavy mineral buildup on temperature and pressure relief valve, and evidence of hard water conditions; also noted contaminated condensate drain pan with brown staining and biological growth requiring attention during future service visit.

Completed comprehensive furnace tune-up on 9+ year old heating system in morning timeframe per customer availability. Performed full inspection of furnace unit located in utility closet alongside water heater, including examination of heat exchanger, burner assembly, blower components, and ductwork connections. Verified proper operation of digital control panel, tested safety controls, cleaned burners, checked gas pressure and combustion efficiency, inspected flue system and venting, and confirmed adequate airflow through supply and return ducts. All components found operating within manufacturer specifications with no immediate safety concerns identified. Unit returned to normal operation with optimal performance parameters.

Completed comprehensive furnace tune-up on a one-year-old system during afternoon appointment. Performed standard maintenance protocol including inspection of all mechanical components, condensate drain system verification, and air filter assessment. All equipment found to be operating within normal parameters with no deficiencies noted.

Completed comprehensive BFMA furnace tune-up and preventative maintenance on residential gas heating system. Performed full system inspection including burner assembly cleaning, flame sensor maintenance, heat exchanger examination, blower motor lubrication, air filter replacement, and thermostat calibration. Verified proper combustion efficiency, tested all safety controls, and confirmed optimal airflow throughout the ductwork system.

Completed comprehensive BFMA tune-up service on residential furnace and humidifier system located in utility closet. Performed full furnace inspection including burner assembly, heat exchanger, blower motor, and gas connections; verified proper operation and safety controls. Serviced humidifier unit with #10 pad replacement, checked water supply line, and confirmed proper humidity output and drainage function.

Responded to service call for water pooling under four-month-old furnace near AC drain line. Upon inspection, identified constant leak originating from condensate drainage system. Examined HVAC equipment including R-454B refrigerant system with A2L safety classification manufactured in April 2026. Inspected internal components including evaporator coil assembly with copper refrigerant lines, condensate pan, and drainage connections. Traced leak source to condensate drain line issue at PVC connection point. Documented equipment condition and drainage system configuration with photographs showing piping connections, coil assembly, and affected area. Cleared blockage and verified proper drainage flow through white PVC condensate line to eliminate standing water beneath unit.