Geneva IL Heating and Air Conditioning Service

Completed comprehensive air conditioning tune-up on 4-year-old Amana condenser unit. Performed standard maintenance protocol including inspection of condenser coil fins, electrical connections at disconnect box, and refrigerant system components. All components found operating within normal parameters, unit tested and confirmed functioning properly for continued cooling season operation.

Completed non-member air conditioning tune-up on a 3-year-old Trane outdoor condensing unit. Performed comprehensive system inspection including visual examination of exterior cabinet condition, electrical disconnect, refrigerant lines, and concrete pad placement. Accessed electrical compartment to inspect dual-run capacitor, contactor, wiring connections, and wire terminals for proper operation and secure connections. All components found in good working condition with no immediate repairs needed. System operating within normal parameters.

Completed comprehensive air conditioning tune-up maintenance service for residential system. Performed electrical diagnostics using digital multimeter to test voltage and amperage at system components in attic space, verifying proper electrical connections and circuit integrity across all wiring. Inspected water heater installation in utility closet, noting circulation pump operation and plumbing connections as part of overall system assessment to ensure home readiness.

Responded to a sump pump failure in a basement utility area. Replaced the failed sump pump system, including new discharge piping and electrical connections. Verified proper operation of the new pump, tested float switch functionality, and ensured adequate drainage through the existing PVC discharge lines that run vertically along the foundation wall to the exterior discharge point.

# BFMA Tune Up - Dual AC System Maintenance Completed comprehensive BFMA tune-up service on two residential air conditioning systems, ages 7 and 11 years. Performed maintenance on Trane XR model outdoor condenser unit, which showed moderate exterior soiling and weathering consistent with age. Removed top cover to access internal components and inspected cylindrical condenser coil assembly, which exhibited heavy accumulation of dirt, dust, and debris between fins throughout the coil surfaces. Cleaned condenser coils to remove environmental contaminants and restore proper airflow through fin spaces. Performed standard tune-up procedures including electrical connection inspection, refrigerant level verification, capacitor testing, and operational testing of both systems. Verified proper amperage draw on compressor and fan motor. Checked thermostat calibration and system cycling. Both units returned to normal operating parameters following maintenance procedures. Documented equipment co

Performed comprehensive air conditioning tune-up on 4-year-old residential outdoor condensing unit. Conducted electrical diagnostics using clamp meter, measuring amperage draw at 6.1 amps and verifying proper voltage to compressor and capacitor. Inspected condenser coils, which showed normal wear and minor debris accumulation from outdoor exposure beneath deck structure. Verified all electrical connections, tested capacitor performance, and confirmed unit operational parameters within manufacturer specifications.

Completed comprehensive BFMA tune-up service on an 11-year-old residential air conditioning system. Performed full system inspection including electrical disconnect verification, compressor operation assessment, refrigerant line inspection, and exterior unit evaluation. All components found operating within normal parameters with unit showing typical wear for age; system left in proper working condition for continued seasonal operation.

# Navien Boiler Valve Replacement Successfully replaced the water adjustment and check valves on a Navien boiler system. The faulty valve assembly, which included integrated black corrugated pipe fittings and white valve housing components, was removed and replaced with new OEM parts. The replacement assembly featured a T-shaped black plastic connector with ribbed sections for secure hose connections, joined to a white valve body with mounting brackets and internal control mechanisms. All connections were properly secured and tested for proper operation. Parts were pre-staged at headquarters prior to service call, ensuring efficient completion of the repair.

Repaired dripping shower faucet in residential bathroom by replacing worn cartridge and seals on 15-year-old chrome fixture. Tested water flow and temperature control to ensure proper operation with no leaks detected upon completion.

Conducted HVAC assessment for residential air conditioning system replacement. Customer expressed interest in replacement options for existing 15-year-old system. Evaluated indoor furnace unit located in basement mechanical room showing age-related wear, and inspected outdoor condenser unit positioned against exterior wall near chimney. Documented current equipment condition and configuration including ductwork connections and electrical service. Prepared comprehensive replacement estimate presenting multiple air conditioning and coil upgrade options to improve system efficiency and reliability.

Conducted comprehensive site evaluation for full HVAC system replacement serving first floor. Documented existing dual-furnace configuration in mechanical room, including current electrical distribution panel with dedicated circuits for Furnace 1, Furnace 2, AC unit, water heater, and associated outlets. Assessed existing ductwork infrastructure, PVC venting system, and equipment placement to develop accurate replacement proposal for aging HVAC equipment.

Responded to service call for non-operational roof exhaust fan that had been inoperative for several years. Inspected motor assembly and fan blades within HVAC system, documented existing wiring connections including electrical conduit, and assessed ventilation system components to determine necessary repairs for proper exhaust venting through roof-mounted unit.

Conducted comprehensive site assessment for boiler replacement estimate at residential property. Evaluated existing hydronic heating system components including zone valves, circulation pumps, and associated piping infrastructure located in attic space. Documented current system conditions showing aged flexible ductwork connections, deteriorated insulation backing on surrounding framing, and existing brass valve assemblies with filtration components. Assessed accessible plumbing connections, PVC venting configuration, and mechanical equipment placement for replacement specifications. Photographed installation area to determine proper equipment sizing, clearance requirements, and integration points for new boiler system.

Responded to service call for boiler system with uneven heating throughout the home that had persisted for approximately two weeks. Upon inspection, discovered severely corroded heat exchanger with extensive rust formation on metal fins and internal components, indicating advanced deterioration and potential safety concerns. Documented equipment condition showing significant oxidation on copper piping, heat exchanger degradation, and debris accumulation within the unit, requiring immediate attention to restore proper heating distribution and system safety.

Completed comprehensive BFMA tune-up on residential furnace system during morning service window. Performed standard maintenance protocol including system inspection, component testing, and filter assessment. Removed and documented severely clogged air filter showing significant dust and debris accumulation, restricting airflow and reducing system efficiency. Inspected gas connections, refrigerant lines, brass fittings, and electrical connections for proper operation and safety compliance. All mechanical components, copper lines, and mounting hardware found secure and functioning within manufacturer specifications. System restored to optimal performance with improved airflow capacity.

# Service Report: Residential No Heat Call Responded to a no heat call for a residential two-unit system where the downstairs unit was not heating and displaying error code E21 (failure to establish flame). Upon inspection, diagnosed and addressed the flame establishment issue affecting the heating operation. Inspected internal mechanical components including the manifold assembly, gas valve connections, and associated wiring to identify the root cause of the ignition failure. Restored proper heating function to the affected unit and verified system operation with successful flame establishment and normal heating cycle completion.

Conducted furnace replacement consultation for a 20-year-old existing Carrier heating system. Assessed current equipment configuration, documented existing ductwork connections and air handler setup, and reviewed available upgrade options with customer including applicable manufacturer promotions and association member discounts.

# Service Summary Completed comprehensive furnace tune-up on 3-year-old unit per seasonal maintenance special. Customer reported unusual noise during operation requiring diagnostic evaluation. # Work Performed Conducted full system inspection and preventative maintenance service on residential forced-air furnace system. Performed visual examination of heat exchanger for cracks or deterioration. Inspected burner assembly, flame sensor, and ignition system for proper operation and wear. Cleaned burner ports and verified proper flame pattern and color during combustion cycle. Evaluated blower motor assembly and checked for unusual vibrations or bearing noise that could correlate with customer's reported sound concern. Inspected blower wheel for debris accumulation and balance issues. Verified proper motor amperage draw and capacitor function. Examined air filter condition and confirmed adequate airflow through system. Tested all safety controls including limit switches, pressure swit

Successfully installed and commissioned new AC system. Completed all installation worksheet requirements and verified proper operation of system. Documented coil serial number and took reference photos of installation components including PVC drainage, copper refrigerant lines, and system connections.

Responded to after-hours call for heating system failure in 1990s model equipment that had been previously serviced without resolution. Performed diagnostic inspection of both the indoor furnace unit and outdoor condenser, documenting the condition of the mechanical room setup including water heater integration and associated PVC/copper piping network. System requires follow-up service due to age-related component deterioration.